Open official notice

Motorcycles (Honda GB350, GB350 S) - Repair

Official notice

9 Nov 2023

Last checked

27 Oct 2026

RecallScope risk estimate:HighCAA Japan

An official CAA Japan notice concerns Motorcycles (Honda GB350, GB350 S) - Repair. Defects in the brake light (rear stop switch) and electrical equipment (bank angle sensor). ■ Defective components (part names): ① Brake light (rear stop switch). ② Electrical equipment (bank angle sensor). ■ Description and cause of the structure, equipment or performance considered noncompliant with standards: ① Some rear stop switches have insufficient durability because of an inappropriate material formulation for the waterproofing grommet. Ozone degradation may therefore cause cracks in the grommet. If rainwater or other moisture enters the switch and reaches its contacts, the brake light may illuminate even when the brake pedal is not pressed. In the worst case, poor electrical continuity at the switch contacts may prevent the brake light from illuminating even when the brake pedal is pressed. ② In the device that stops the engine when the motorcycle falls over (bank angle sensor), inappropriate molding work and mold management for the sensor holder have resulted in inadequate sealing in some holders. If water enters the sensor during riding in rain or similar conditions, the circuit on the internal circuit board may short-circuit, falsely detecting that the motorcycle has fallen over and potentially stopping the engine while riding. Published 2023-11-09.

What to do now

(Recall notification number) 5410 ■ Corrective measures: ① Replace the rear stop switch with a properly manufactured part on all vehicles. ② Replace the bank angle sensor with a properly manufactured part on all vehicles.

Units affected

17,151

Recall number

5410

Official notice

2023-11-09

The hazard

Defects in the brake light (rear stop switch) and electrical equipment (bank angle sensor). ■ Defective components (part names): ① Brake light (rear stop switch). ② Electrical equipment (bank angle sensor). ■ Description and cause of the structure, equipment or performance considered noncompliant with standards: ① Some rear stop switches have insufficient durability because of an inappropriate material formulation for the waterproofing grommet. Ozone degradation may therefore cause cracks in the grommet. If rainwater or other moisture enters the switch and reaches its contacts, the brake light may illuminate even when the brake pedal is not pressed. In the worst case, poor electrical continuity at the switch contacts may prevent the brake light from illuminating even when the brake pedal is pressed. ② In the device that stops the engine when the motorcycle falls over (bank angle sensor), inappropriate molding work and mold management for the sensor holder have resulted in inadequate sealing in some holders. If water enters the sensor during riding in rain or similar conditions, the circuit on the internal circuit board may short-circuit, falsely detecting that the motorcycle has fallen over and potentially stopping the engine while riding.

How to check if you're affected

Compare the product name and identifiers below with the item you own. Check the official notice for the affected products and next steps.

Models

2BL-NC59

Recall Numbers

5410

Checked manually this time?

Add your VIN to the app Watchlist to receive alerts for matching official notices.

Turn on automatic VIN checks

Affected products

Product 1

ホンダ「GB350」「GB350 S」

Units affected

17,151

Hazard

Defects in the brake light (rear stop switch) and electrical equipment (bank angle sensor). ■ Defective components (part names): ① Brake light (rear stop switch). ② Electrical equipment (bank angle sensor). ■ Description and cause of the structure, equipment or performance considered noncompliant with standards: ① Some rear stop switches have insufficient durability because of an inappropriate material formulation for the waterproofing grommet. Ozone degradation may therefore cause cracks in the grommet. If rainwater or other moisture enters the switch and reaches its contacts, the brake light may illuminate even when the brake pedal is not pressed. In the worst case, poor electrical continuity at the switch contacts may prevent the brake light from illuminating even when the brake pedal is pressed. ② In the device that stops the engine when the motorcycle falls over (bank angle sensor), inappropriate molding work and mold management for the sensor holder have resulted in inadequate sealing in some holders. If water enters the sensor during riding in rain or similar conditions, the circuit on the internal circuit board may short-circuit, falsely detecting that the motorcycle has fallen over and potentially stopping the engine while riding.

Where it was sold

Retailer information is not currently available in RecallScope. Check the official notice for distribution details.

Location 1

JP · Japan

Affected area 1

JP · Japan

Company & contacts

Brand

Manufacturer

本田技研工業株式会社

Phone

0120-086819

Brand: Honda. Contact: 本田技研工業株式会社. Phone 0120-086819.

Source & status

Source

Tier

official

Category

VEHICLES

Official classification

消費者庁 — 修理

Recall details

Recall number

5410

Event id

CAA-00000031544

Units affected

17,151

Source tier

official

Documents, notices & source

See the official notice and source documents for full details.

View full official notice
Something wrong on this page?

Weekly recall digest

Get next week's recalls before you need them.

One email every Monday — official-source recalls for your country, and nothing else. Unsubscribe from any email.

The digest arrives once a week. For matching recall alerts after notices are processed, get the app.

This recall was published 9 Nov 2023. The next one won't wait for you to search.

RecallScope checks listed publishers for the brands and VINs you follow, and can alert you when a matching notice is processed.

apple-buttongoogle-button