Image available on the official notice.
Motorcycles (Kawasaki D-TRACKER X and others) - Inspection and repair
Official notice
30 May 2011
Last checked
28 Oct 2026
An official CAA Japan notice concerns Motorcycles (Kawasaki D-TRACKER X and others) - Inspection and repair. ■Defective components (part names): ① Lighting equipment (headlamp). ② Fuel system (fuel tank). ③ Electrical equipment (electronic control unit, tip-over sensor). ④ Electrical equipment (electrical wiring). ■Condition and cause of the noncompliant structure, equipment or performance: ① Improper routing of the headlamp bulb wiring and main harness may cause poor contact between the bulb terminals and socket terminals. Continued use in this condition may increase electrical resistance between the terminals, raising their temperature and damaging the terminals or wiring, potentially causing the low beam, high beam or both to stop working. ② The fuel tank mounting structure is inappropriate, potentially leaving a gap between the fuel tank and its securing rubber damper and providing insufficient vibration damping. Continued use in this condition may cause vibration-induced cracks in the welds at the fuel tank mounting points and, in the worst case, fuel leakage. ③ Waterproofing of the wiring between the fuel-injection electronic control unit (ECU) and the tip-over sensor is insufficient. Water encountered during washing or riding in rain may travel inside the wiring and enter the connections between the wiring and the ECU and tip-over sensor. Continued use in this condition may cause corrosion of the connection terminals and poor electrical continuity and, in the worst case, the engine may stop. ④ Improper routing of the wiring connected to the ECU may allow it to contact a frame tube. Continued use in this condition may wear away the wiring insulation, causing the conductor to short-circuit against the frame tube and, in the worst case, the engine may stop. Published 2011-05-30.
What to do now
(Recall) 2748 ■Corrective measures: ① On all vehicles, inspect the bulb terminals and replace the bulb with a new one if damaged. Also replace the headlamp bulb wiring with a modified part and add a guard behind its connection. ② On all vehicles, inspect the welds at the fuel tank mounting points and replace the tank with a new one if fuel seepage or leakage is present. Also, on all vehicles, replace the tank securing rubber damper with a new one and replace the collar and bolt with modified parts. In addition, inspect the gap between the tank support rubber damper and the tank bottom plate, and attach an additional support rubber damper appropriate to the gap to the tank bottom plate. ③ On all vehicles, inspect the terminals at the connections between the wiring and the ECU and tip-over sensor. If corrosion is found, replace the ECU or tip-over sensor together with the wiring with new parts. Also apply grease to these connections to inhibit corrosion caused by water entering them. ④ On all vehicles, inspect the wiring in question and repair any damage. Also replace the ECU mounting bracket with a modified part and add a protective cover to the wiring.
Recall number
2748
Official notice
2011-05-30
The hazard
The hazard
■Defective components (part names): ① Lighting equipment (headlamp). ② Fuel system (fuel tank). ③ Electrical equipment (electronic control unit, tip-over sensor). ④ Electrical equipment (electrical wiring). ■Condition and cause of the noncompliant structure, equipment or performance: ① Improper routing of the headlamp bulb wiring and main harness may cause poor contact between the bulb terminals and socket terminals. Continued use in this condition may increase electrical resistance between the terminals, raising their temperature and damaging the terminals or wiring, potentially causing the low beam, high beam or both to stop working. ② The fuel tank mounting structure is inappropriate, potentially leaving a gap between the fuel tank and its securing rubber damper and providing insufficient vibration damping. Continued use in this condition may cause vibration-induced cracks in the welds at the fuel tank mounting points and, in the worst case, fuel leakage. ③ Waterproofing of the wiring between the fuel-injection electronic control unit (ECU) and the tip-over sensor is insufficient. Water encountered during washing or riding in rain may travel inside the wiring and enter the connections between the wiring and the ECU and tip-over sensor. Continued use in this condition may cause corrosion of the connection terminals and poor electrical continuity and, in the worst case, the engine may stop. ④ Improper routing of the wiring connected to the ECU may allow it to contact a frame tube. Continued use in this condition may wear away the wiring insulation, causing the conductor to short-circuit against the frame tube and, in the worst case, the engine may stop.
How to check if you're affected
How to check if you're affected
Compare the product name and identifiers below with the item you own. Check the official notice for the affected products and next steps.
Recall Numbers
Checked manually this time?
Add your VIN to the app Watchlist to receive alerts for matching official notices.
Turn on automatic VIN checksAffected products
Affected products
Product 1
Hazard
Where it was sold
Where it was sold
Retailer information is not currently available in RecallScope. Check the official notice for distribution details.
Location 1
Affected area 1
Company & contacts
Company & contacts
Brand: Kawasaki. Contact: モーターサイクル&エンジンカンパニー品質保証本部. Phone 078-921-1421.
Source & status
Source & status
Recall details
Recall details
Recall number
Event id
Source tier
Documents, notices & source
See the official notice and source documents for full details.
View full official noticeWeekly recall digest
Get next week's recalls before you need them.
One email every Monday — official-source recalls for your country, and nothing else. Unsubscribe from any email.
The digest arrives once a week. For matching recall alerts after notices are processed, get the app.